Winter 2008 Formula Interior Upgrade Project

We did that two winters ago :sifone:
 

Attachments

  • IMG_2261.jpg
    IMG_2261.jpg
    61.8 KB · Views: 10
  • boat 96 382 123.jpg
    boat 96 382 123.jpg
    69.1 KB · Views: 21
  • boat 96 382 124.jpg
    boat 96 382 124.jpg
    95.1 KB · Views: 19
I agree with those that say pull the dash now. I bet ya a cold beer that you will wish you would have if you don't. Good luck!
 
I finally made a decision and ordered my gauges. Ordered them on Tuesday at 3:30 and by Thursday at noon they were on my doorstep.
 

Attachments

  • 001.jpg
    001.jpg
    92.6 KB · Views: 20
Mightaswellanoma.
"Well, I tore this out, so I might-as well..."

I've had this disease for a long time, yet to find a cure short of a large checkbook.
 
Here are a couple pictures of the cover I had made for it. They aren't the best quality because they are cell phone pictures.
 

Attachments

  • 041 (2).jpg
    041 (2).jpg
    67.8 KB · Views: 8
  • 043 (2).jpg
    043 (2).jpg
    73.3 KB · Views: 9
New port panels, new shift and trim panel. The switches will be white I just havn't put the new ones on yet. I attempted to save 2 trim panels that still looked good but ended up tearing them up pulling the backrest out. I am going to get them recovered tomorrow morning and hopefully get them put back in tomorrow afternoon along with the seats and gauge panels. If I dont get it done tomorrow I will have to get it done Wednesday for sure. I leave for the Caribbean next Wednesday and would like to have it done before I go.:D
 

Attachments

  • 017.jpg
    017.jpg
    71.2 KB · Views: 9
  • 015.jpg
    015.jpg
    58 KB · Views: 11
Worked all day today on my boat and I have all trim panels in. I replaced all hardware with stainless. Bolster seat brackets are mounted back in and ready for the seats to be put on them. I have my new depth finder mounted, cables ran and puck secured to fiberglass. I also have my trim indicator wired up and working. All trim switches are white now with stainless screws. Deptch finder is hooked up and ready to go. I aslo installed the grab bars on both side of the boat today. My electrical guy is going to try to get the rest of the gauges in tomorrow and then we will finish it up on Friday night. It has been a long couple days but progress has been made. I would really like to put new sticks in but I think the checkbook says wait till next winter. I was to tired to take pictures today when I got done so I will get some taken on Friday when I go back to work on it.
 
very nice...... I have my 400SS interior being done right now, should install in the next couple of weekends!!!
Pat
 
Finally all back together!!

Here are some pictures.
 

Attachments

  • New Engine Hatch.jpg
    New Engine Hatch.jpg
    50.8 KB · Views: 4
  • Hatch and Back Seat 1.jpg
    Hatch and Back Seat 1.jpg
    34.1 KB · Views: 3
  • Hatch and Back Seat 2.jpg
    Hatch and Back Seat 2.jpg
    35.8 KB · Views: 3
New Dash Panels, Gauges, and Steering Wheel.
 

Attachments

  • New Port Dash.jpg
    New Port Dash.jpg
    39.6 KB · Views: 4
  • New Dash, Gauges, and Wheel.jpg
    New Dash, Gauges, and Wheel.jpg
    54.9 KB · Views: 3
  • New Dash 1.jpg
    New Dash 1.jpg
    54.3 KB · Views: 4
New Step Plates and Cup Holders.
 

Attachments

  • New Step Plate and Cup Holder 1.jpg
    New Step Plate and Cup Holder 1.jpg
    37.3 KB · Views: 3
  • New Step Plate and Cup Holder 2.jpg
    New Step Plate and Cup Holder 2.jpg
    36.1 KB · Views: 4
Back
Top