Thad Allen's Apache + The Birth of the Cheetah Cat

[Steve 1]

Dave Artie ,Here is how that mold system worked the stringers were done then the Bulkheads were placed inside laying down, the deck mold with the finished part was then placed on the hull mold (the cutting flanges were "Keyed") then 360 glass, the bulkheads were then stood in place and glassed in then the deck mold was removed as shown here.

That new Sport deck would just be done in the same manner with the molds flange to flange glassed then demolded.

 

[Premier Perf]

Steve1 i tried PM you but it says you can't recieve. PM your e-mail

 

[Steve 1]

Steve1 i tried PM you but it says you can't recieve. PM your e-mail

Will do thanks for bringing that to my attention.

 

[Steve 1]

Steve1 i tried PM you but it says you can't recieve. PM your e-mail

Should be good now.

 

[Steve 1]

This Cheetahcat I am getting ready for lamination had a folded pad and a tunnel that was a little different. I was doing some wet bagging that choppergun had a roll of Carbon fiber tow on it.This boat was to get Navy style S-Glass not S-2.

 

[Steve 1]

Dave How are you doing with the Vacuum system?

 

[Steve 1]

Here is a full tunnel on a pleasure boat this goes with a post I made on the New Cheetahcat thread.

 

[glassdave]

Dave How are you doing with the Vacuum system?

still working on it . . . .this thing SUCKS! lol :sifone:


I have a project i want to infuse. Havnt done that yet. I'm having the control piece made at the moment and i also need to get a new gauge and trap for this system.

 

[Steve 1]

still working on it . . . .this thing SUCKS! lol :sifone:


I have a project i want to infuse. Havnt done that yet. I'm having the control piece made at the moment and i also need to get a new gauge and trap for this system.

LOL Vacuum does Suck I just used cheap pressure pots for a trap and rig a good filter system for the pump to keep airborne crap away from valuable moving parts. Regards.

 

[glassdave]

LOL Vacuum does Suck I just used cheap pressure pots for a trap and rig a good filter system for the pump to keep airborne crap away from valuable moving parts. Regards.

same here, been getting two quart paint pots from Harbor Freight and stripping them down to work as a trap. Work great and i think the last one was under twenty bucks. I have been pretty good about keeping waste in the bleeder ply and out of the lines. Got a real nice filter and oil mist eliminator for this one.

Hey whats a gas ballast? Do i need that? Thanks

 

[Steve 1]

same here, been getting two quart paint pots from Harbor Freight and stripping them down to work as a trap. Work great and i think the last one was under twenty bucks. I have been pretty good about keeping waste in the bleeder ply and out of the lines. Got a real nice filter and oil mist eliminator for this one.

Hey whats a gas ballast? Do i need that? Thanks

I never used or needed one and I had oil filled pumps before.

 

[Steve 1]

I have a KRYPTON Infusion system where large diameter feeds are used,I spiral cut cheap PVC and just use plastic valves instead of pinching the feeds off and we use a single common feed Reservoir instead of a half dozen or more buckets all sitting around the work,also I can shut one trap out of the system and drain it into the feed bucked if needed.

The first ones I made out of cheapo Speedaire 2.5 gallon pressure pots I bought from the pawn ,shop Knocked some holes with a hole saw in the lid for the PVC and they worked great. A roll of tacky tape does wonders.

 

[glassdave]

no way! . . . . because i pawned some of those years ago to buy good ones


Just kidding lol



I like the large feed lines i see you using. I have mostly used the clear half inch tubing with the small system. Think i may hafta step it up for this larger pump.

 

[Steve 1]

no way! . . . . because i pawned some of those years ago to buy good ones


Just kidding lol



I like the large feed lines i see you using. I have mostly used the clear half inch tubing with the small system. Think i may hafta step it up for this larger pump.

Yes I use the Home Depot Lowes Infusion supplies, The cheap Plastic ball valves take all the fun out of it.

 

[Offshore Ginger]

Yes I use the Home Depot Lowes Infusion supplies, The cheap Plastic ball valves take all the fun out of it.

:rofl::rofl::rofl: Great stuff from post 1047 to this on Infusion supplies but did you both know that you can save big money at Menard's :seeya: .

 

[Steve 1]

:rofl::rofl::rofl: Great stuff from post 1047 to this on Infusion supplies but did you both know that you can save big money at Menard's :seeya: .

Artie thanks for the info LOL

 

[cigrunner38]

Curious what would happen if the bow "nipple" were larger to the packing of air.

Help me out here. Wouldn't it be less air in the tunnel? Or would it make it more left to right

 

[Steve 1]

Dave keep us updated that is a beautiful pump.

 

[Steve 1]

Curious what would happen if the bow "nipple" were larger to the packing of air.

Help me out here. Wouldn't it be less air in the tunnel? Or would it make it more left to right

Nipple?????

 

[Steve 1]

Dave here is a Regulator (lower Arrow) the upper is a wall mounted vacuum gauge in PSI that I found in some Iraqi stolen booty ,the entire shop has a large pipe going around it with drops about every 12-16 feet or so. The way I had that system is the regulator could be shut out of the system with a valve.